SUPREME SEAL

EAGLE SUPREME SEAL

• Clear acrylic for all types of concrete
• Use on driveways, porches, sidewalks, pool decks, patios, concrete pavers or most horizontal concrete substrates
• High-gloss, wet look finish
• Revitalizes old concrete
• Protects from water, salt, freeze/thaw damage and lessens rock popping
• Solvent-based for best adhesion
• High solids pure acrylic
• Beautifully enhances decorative, colored and acid stained concrete
• Non-yellowing and UV resistant
• Self-priming and reseals easily

 

LIMITATIONS

• Not suitable for clay or terra cotta bricks
• Not suitable for asphalt or other non-masonry materials
• Not effective on stone surfaces

SUGGESTED TOOLS & MATERIALS NEEDED

1. Pressure Washer using 2500-3000 PSI
2. Solvent resistant pump-up sprayer (optional)
3. Solvent resistant roller with ¾” to 1 ¼” nap depending on surface
4. Solvent resistant roller tray
5. Eye protection and gloves
6. EAGLE CLEANER DEGREASER & NEUTRALIZER
7. EAGLE ETCH & CLEAN (when needed)

 

**NOTE: ALWAYS TEST FIRST – We strongly suggest, before applying any EAGLE products, you should always check the suitability and desired finish on a small area before starting your application. When applying to a test area, you should use the same surface preparation process and apply using the same equipment you will be using to complete the full general application.

 

PREPARATION

Since many sealer application issues can be avoided by properly preparing your concrete, always take the time needed to prepare your surface. Preparation is key.

 

Step 1: Clean any dirt, wax, grease, oil and other contaminants that may interfere with the sealer from adhering to the surface. This includes removing any prior coatings, UNLESS previous coating is the same or a similar solvent-based sealer (for instructions on removing old sealer or preparing a prior water-base sealer for additional maintenance coats, click here).

 

Clean oily concrete with EAGLE CLEANER DEGREASER & NEUTRALIZER. Use a medium to firm bristle brush for heavily oiled spots.

 

Step 2: Concrete must be porous enough to accept water. If concrete surface is smooth (similar to a garage floor), it will be necessary to etch the substrate using EAGLE ETCH & CLEAN. Dense concrete surfaces may require mechanical preparation to accept sealer.

 

 

Step 3: PRESSURE WASH. ALWAYS rinse surface well using a pressure washer with 2500-3000 psi. It is recommended to allow 24 hours for concrete surface to completely dry after pressure washing (may take longer to dry if humid environmental conditions exist or if the substrate is indoors). For pavers, sweep away any loose sand washed out through pressure washing.

 

SURFACE & AIR TEMPERATURES

For best results, apply when surface and air temperatures are above 50° F and below 95° F. Applying sealer on windy days may cause rapid surface drying preventing proper curing of sealer and should be avoided.

 

KEEP IN MIND

If applying in extremely hot conditions, you will have to account for faster dry time, and work accordingly, to avoid stringing (i.e. “cobwebbing”) and physically inducing air into the film, due to overworking, as the viscosity (thickness) of the sealer rapidly increases.

 

APPLICATION

For best results, always apply SUPREME SEAL in two (2) thin coats to achieve net square foot coverage rate. Do not thin product. 

 

• For EXTERIOR application ONLY.
• Perform a test to ensure sealer compatibility.
• Brush may be used where roller won’t reach.
• Do not pour directly from container onto concrete.
• 1 ¼” nap roller for exposed aggregate.
• 1” nap roller for textured surfaces.
• ¾” short nap roller for smooth surfaces.

 

Keep roller soaked and apply vertically, or horizontally, to entire area, maintaining a wet edge to avoid roller marks. Wait until the surface is tack-free (approx. 4 hours) before applying a second coat by cross-rolling perpendicular to the first coat ensuring complete coverage. Foot traffic should be avoided for 4-6 hours. Vehicle traffic should be avoided for 48 hours.

 

• Do not apply if rain is imminent.
• Cooler temperatures or increased humidity may slow the drying time.

 

NET COVERAGE RATE

In order to achieve the suggested net coverage rate, it is strongly recommended to apply in two (2) thin coats. To calculate your total area square footage (length X width = total square feet) to determine the amount of product you’ll need to properly meet the suggested net coverage rates. SEE BELOW. 

 

• Smooth Troweled (etch required): 300 ft² per gallon
• Textured or Stamped: 200 ft² per gallon
• Broom Swept: 200 ft² per gallon
• Exposed Aggregate and Pavers: 100 ft² per gallon

 

EXAMPLE: If you are sealing a traditional driveway that has a broom swept finish and 1000 total square feet to cover, you will need 5 gallons of sealer. You will use 2 ½ gallons for your first coat and the remaining 2 ½ gallons for the second coat to achieve the suggested net coverage of 200 square feet per gallon.

 

CLEANUP

Clean up tools with Xylene, Toluene or Lacquer Thinner.

Do not use Paint Thinner, Mineral Spirits or water.

 

MAINTENANCE

Clean sealed surface with water only. Reseal surface as needed, but not more than every two years to prevent buildup of sealer.

24 HOUR & EMERGENCY INFORMATION

INFOTRAC: (800) 535-5053

 

WARNING:

Strong solvent smell.

 

COMBUSTIBLE

EYE, SKIN AND RESPIRATORY IRRITANT

KEEP OUT OF REACH OF CHILDREN

 

Contains Aromatic Naphtha. Do not use near heat, sparks or open flames. Avoid contact with eyes and prolonged contact with skin. Use only with adequate ventilation. Do not inhale vapors. Do not ingest.

 

FIRST AID

• In case of eye contact, flush with water for 15 minutes.
• In case of skin contact, wash thoroughly with soap and water.
• If swallowed, do not induce vomiting.
• Immediately contact hospital ER or physician.
• If vapors are inhaled or breathing becomes difficult, move person to fresh air immediately.
• Seek medical attention if skin, eye or respiratory irritation persist.

 

See Safety Data Sheet for more information

 

 

TECHNICAL DATA

Color/Type:              Clear Liquid

Active Content:        75%

Total Solids:             25%

VOC:                        Standard <700 g/L

Flash Point:              105° F

Freeze Point:            N/A

Storage:                    Inside, well ventilated. Keep container in dry area.

Shelf Life:                 2 years in tightly sealed, unopened container

 

Meets or exceeds specification ASTM C1315

 

STORAGE AND HANDLING

DO NOT modify sealer mix with other chemicals. Store in a cool dry place away from potential ignition sources. Keep container tightly sealed when not in use. Published shelf-life based upon upright storage of manufacturer-sealed containers kept in a cool dry area. Store in temperatures from 45⁰F to 100⁰F. Always dispose of unused product and container in accordance with local, state and federal guidelines.

Sealer Type: Acrylic

 

Net Weight (lbs.):

• 5 Gallon - 45
• 1 Gallon - 9

 

Recommended Surfaces:

• Smooth Troweled - Yes
• Textured or Stamped -Yes
• Broom Swept - Yes
• Exposed Aggregate - Yes
• Pavers - Yes
• Color, Dye or Stained Concrete - Yes

 

Net Coverage Rate (2 coats):

• Smooth Troweled - 300 ft2 per gallon
• Textured or Stamped - 200 ft2 per gallon
• Broom Swept - 200 ft2 per gallon
• Exposed Aggregate - 100 ft2 per gallon
• Pavers - 100 ft2 per gallon

 

Number of Coats:

2

 

Application Method:

Spray or Roller 

 

Available Color(s):

Clear

 

Interior/Exterior:

Exterior only

 

Sheen:

High Gloss

 

Dry to Touch:

2 - 4 hrs.

 

Foot Traffic:

4 hrs.

 

Vehicle Traffic:

48 hrs.

 

Water/Solvent Base:

Solvent

 

Low VOC:

N/A

 

Odor Type:

Strong Solvent

 

Warranty:

None

FREE SHIPPING is Standard UPS Ground shipping on parcel and residential delivery for all purchases over $50.00 made on eaglesealer.com, and does NOT include EXPRESS or EXPEDITED shipping. Some exclusions apply. Due to Federal DOT shipping regulations with paint related products, overnight, air deliveries or Solvent Based Low VOC sealers are NOT available for standardized shipping. Please contact our office for shipping options. EAGLE reserves the right to change or end this offer at any time.

 

EAGLE cannot ship to APO/FPO, P.O. Boxes, Alaska, Hawaii or U.S. Territories. For most shipments, please allow 1-2 business days for order processing and 3-5 business days for standard ground delivery in addition to order processing time. Holiday deliveries may be delayed so please take into consideration.

 

RETURN POLICY

If you would like to return any EAGLE product, we will issue a refund under the following conditions: (1) the product is returned to our facility within 30 days from the receipt of the product. (2) The product must be returned unopened and in its original condition. (3) Customer is responsible for return shipping charges, and a 20% restocking fee per order. NO EXCEPTIONS. (4) A refund will be issued within 7 days of returned product received by EAGLE I.F.P. Company, minus the 20% restocking fee AND minus return shipping charges incurred. Collect shipment will not be accepted. Refund will be issued to original payment method ONLY. Return intructions here.

Since Manufacturer has no control over handling, use or storage; no guarantee express or implied, is offered. The suitability of the product for use shall be solely up to the user. Manufacturer retains the right to venue.