EAGLE NATURAL SEAL is the ideal sealer for protecting your concrete without changing its natural appearance. NATURAL SEAL is a deep penetrating water repellent sealer formulated using a proprietary hybrid of Silane and Siloxane. NATURAL SEAL provides exceptional water repellency to porous construction materials such as concrete, bricks, stone, masonry blocks, mortar, and grout.
NATURAL SEAL is excellent at protecting against rain, salt, freeze/thaw and most weathering conditions mother nature can impose on concrete or other masonry surfaces.
NET COVERAGE RATE: Approx. 200 sq. ft. per gallon, depending on the porosity of the substrate and can usually be achieved in one (1) coat. Additional coats may be required ONLY on very porous surfaces.
TECHNICAL & SAFETY INFORMATION
** PLEASE NOTE:
Due to shipping or VOC regulations, NATURAL SEAL is limited to listed states: AL, AR, AZ, CA, CO, CT, DC, DE, FL, GA, ID, IL, IA, KS, KY, LA, MA, MD, ME, MI, MN, MS, MO, MT, NE, NH, NJ, NM, NC, NY, ND, NV, OH, OK, OR, PA, RI, SC, SD, TN, TX, UT, VA, VT, WA, WV, WI, WY
For more info on VOC regulations in your area click here
NATURAL SEAL
EAGLE NATURAL SEAL
- For vertical or horizontal masonry surfaces
- Special blended Silane and siloxane hybrid formula
- Non-yellowing and UV resistant for maximum outdoor protection
- Dry looking even when surface is wet
- Ideal for all types of masonry surfaces
- Protects masonry surfaces from water, salt, freeze/thaw and weathering
- Water-based and can be used seal interior or exterior
LIMITATIONS
- Not suitable for clay or terra cotta bricks
- Not suitable for very low-porosity substrates such as polished stone
- Not suitable for asphalt or other non-masonry materials
- Not effective on some stone surfaces
SUGGESTED TOOLS & MATERIALS NEEDED
- Pressure Washer using 2500-3000 PSI
- Pump-up sprayer
- Paint roller with ¾” to 1 ¼” nap depending on surface
- Roller tray
- Eye protection and gloves
- EAGLE CLEANER DEGREASER & NEUTRALIZER
- EAGLE ETCH & CLEAN (when needed)
**NOTE: ALWAYS TEST FIRST – We strongly suggest, before applying any EAGLE products, you should always check the suitability and desired finish on a small area before starting your application. When applying to a test area, you should use the same surface preparation process and apply using the same equipment you will be using to complete the full general application.
PREPARATION
Since many sealer application issues can be avoided by properly preparing your concrete, always take the time needed to prepare your surface. Preparation is key.
Step 1: Clean any dirt, wax, grease, oil and other contaminants that may interfere with the sealer from adhering to the surface. This includes removing any prior coatings, UNLESS previous coating is the same or a similar solvent-based sealer (for instructions on removing old sealer or preparing a prior water-base sealer for additional maintenance coats, click here).
Clean oily concrete with EAGLE CLEANER DEGREASER & NEUTRALIZER. Use a medium to firm bristle brush for heavily oiled spots.
Step 2: Concrete must be porous enough to accept water. If concrete surface is smooth (similar to a garage floor), it will be necessary to etch the substrate using EAGLE ETCH & CLEAN. Dense concrete surfaces may require mechanical preparation to accept sealer.
Step 3: PRESSURE WASH. ALWAYS rinse surface well using a pressure washer with 2500-3000 psi. It is recommended to allow 24 hours for concrete surface to completely dry after pressure washing (may take longer to dry if humid environmental conditions exist or if the substrate is indoors). For pavers, sweep away any loose sand washed out through pressure washing.
SURFACE & AIR TEMPERATURES
For best results, apply when surface and air temperatures are above 50° F and below 95° F. Applying sealer on windy days may cause rapid surface drying preventing proper curing of sealer and should be avoided.
APPLICATION
NATURAL SEAL is effective usually after one (1) complete coat (additional applications may be required on more porous surfaces). NATURAL SEAL should always be applied with an airless, or pump-up, sprayer and then followed with cross-rolling for even application. Make sure the area is completely saturated but ensure there is no pooling of product on the substrate surface. Protect other surfaces from overspray, especially glass. Do not thin product.
IMPORTANT: Clean any overspray from non-porous surfaces with a damp cloth before it dries.
- For INTERIOR or EXTERIOR application.
- Perform a test to ensure sealer compatibility.
- Spray vertical surfaces from the bottom up.
- Do not apply if rain is expected within 12 hours.
- 1” nap roller for textured surfaces
- ¾” short nap roller or microfiber applicator for smooth surfaces.
NET COVERAGE RATE
Approx. 200 sq. ft. per gallon, depending on the porosity of the substrate and can usually be achieved in one (1) coat. Additional coats may be required ONLY on very porous surfaces.
To calculate your total area square footage (length X width = total square feet) to determine the amount of product you’ll need to properly meet the suggested net coverage rates.
CLEANUP
Clean up tools with water.
MAINTENANCE
Clean sealed surface with water only. Reseal surface as needed, but not more than every two years to prevent buildup of sealer.
24 HOUR & EMERGENCY INFORMATION
INFOTRAC 1-800-535-5053
WARNING: Harmful if swallowed
EYE, SKIN AND RESPIRATORY IRRITANT
FIRST AID
- Skin: Immediately flush with water for 15 minutes. If irritation develops, get medical attention.
- Eyes: Flush with a gentle but large stream of clean water for 15 minutes, lifting the lower and upper eyelids occasionally. If irritation develops, get medical attention.
- Inhalation: Move to fresh air and provide oxygen if breathing is difficult. Seek medical attention if irritation persists.
- Ingestion: If swallowed, do not induce vomiting. Call a poison center or doctor immediately for treatment advice.
See Safety Data Sheet for more information
TECHNICAL DATA
Color/Type: Cloudy Liquid, Dries Clear
Active Content: 75%
Total Solids: 25%
VOC: Standard <100 g/L
Flash Point: N/A
Freeze Point: 32° F
Storage: Inside, well ventilated. Keep container in dry area.
Shelf Life: 2 years in tightly sealed, unopened container
STORAGE AND HANDLING
AVOID FREEZING. DO NOT modify sealer mix with other chemicals. Store in a cool dry place. Store material in its original container. Keep container tightly sealed when not in use. Published shelf-life based upon upright storage of manufacturer-sealed containers kept in a cool dry area. Store in temperatures from 45⁰F to 100⁰F. Always dispose of unused product and container in accordance with local, state and federal guidelines.
Sealer Type:
Penetrating Water RepellentNet Weight (lbs.):
5 Gallon - 45
1 Gallon - 9
Substrate Surface Type:
Smooth Troweled - Yes
Textured or Stamped - Yes
Broom Swept - Yes
Exposed Aggregate - Yes
Pavers - Yes
Net Coverage Rate:
Approx. 200 sq. ft. per gallon
Number of Coats:
One (1). Porous surfaces may need additional coatTime Between Coats:
4 hrs. if neededApplication Method:
Spray and RollerAvailable Color(s):
ClearInterior/Exterior:
BothSheen:
Dries ClearDry to Touch:
Approx. 2-4 hrs.Foot Traffic:
Approx. 4-6 hrs.Vehicle Traffic:
48 hrs.Water/Solvent Base:
WaterLow VOC:
YesOdor Type:
Low OdorWarranty:
NoneFREE SHIPPING is Standard UPS Ground shipping on parcel and residential delivery for all purchases over $50.00 made on eaglesealer.com, and does NOT include EXPRESS or EXPEDITED shipping. Some exclusions apply. Due to Federal DOT shipping regulations with paint related products, overnight, air deliveries or Solvent Based Low VOC sealers are NOT available for standardized shipping. Please contact our office for shipping options. EAGLE reserves the right to change or end this offer at any time.
EAGLE cannot ship to APO/FPO, P.O. Boxes, Alaska, Hawaii or U.S. Territories. For most shipments, please allow 1-2 business days for order processing and 3-5 business days for standard ground delivery in addition to order processing time. Holiday deliveries may be delayed so please take into consideration.
RETURN POLICY
If you would like to return any EAGLE product, we will issue a refund under the following conditions: (1) the product is returned to our facility within 30 days from the receipt of the product. (2) The product must be returned unopened and in its original condition. (3) Customer is responsible for return shipping charges, and a 20% restocking fee per order. NO EXCEPTIONS. (4) A refund will be issued within 7 days of returned product received by EAGLE I.F.P. Company, minus the 20% restocking fee AND minus return shipping charges incurred. Collect shipment will not be accepted. Refund will be issued to original payment method ONLY. Return intructions here.
Since Manufacturer has no control over handling, use or storage; no guarantee express or implied, is offered. The suitability of the product for use shall be solely up to the user. Manufacturer retains the right to venue.