CHATTAHOOCHEE SEALER

EAGLE CHATTAHOOCHEE SEALER

• Enhances epoxy-set stones with hi-gloss, wet look
• Non-yellowing UV resistant formula
• Makes old epoxy stones look like new
• Protects from water, salt and freeze/thaw damage
• Solvent based for best adhesion
• Clear long-lasting acrylic for years of protection

 

LIMITATIONS

• Not suitable for clay or terra cotta bricks
• Not suitable for asphalt or other non-masonry materials
• Not effective on stone surfaces

SUGGESTED TOOLS & MATERIALS NEEDED

1. Solvent resistant roller with ¾” to 1 ¼” nap depending on surface
2. Solvent resistant roller tray
3. Eye protection and gloves
4. EAGLE CLEANER DEGREASER & NEUTRALIZER

 

**NOTE: ALWAYS TEST FIRST – We strongly suggest, before applying any EAGLE products, you should always check the suitability and desired finish on a small area before starting your application. When applying to a test area, you should use the same surface preparation process and apply using the same equipment you will be using to complete the full general application.

 

PREPARATION

Since many sealer application issues can be avoided by properly preparing your concrete, always take the time needed to prepare your surface. Preparation is key.

 

Step 1: Clean any dirt, wax, grease, oil and other contaminants that may interfere with the sealer from adhering to the surface. This includes removing any prior coatings, UNLESS previous coating is the same or a similar solvent-based sealer (for instructions on removing old sealer or preparing a prior water-base sealer for additional maintenance coats, click here).

 

Clean oily concrete with EAGLE CLEANER DEGREASER & NEUTRALIZER. Use a medium to firm bristle brush for heavily oiled spots.

 

Step 2: Thoroughly rinse surface with high pressure nozzle on your garden hose. It is recommended to allow 24 hours for surface to completely dry after rinsing (may take longer to dry if humid environmental conditions exist or if the substrate is indoors). 

 

**NOTE: It is not recommended to use a pressure washer on Chattahoochee epoxy set surfaces. You run a risk of blowing rocks off the surface.

 

SURFACE & AIR TEMPERATURES

For best results, apply when surface and air temperatures are above 50° F and below 95° F. Applying sealer on windy days may cause rapid surface drying preventing proper curing of sealer and should be avoided.

 

KEEP IN MIND

If applying in extremely hot conditions, you will have to account for faster dry time, and work accordingly, to avoid stringing (i.e. “cobwebbing”) and physically inducing air into the film, due to overworking, as the viscosity (thickness) of the sealer rapidly increases.

 

APPLICATION

For best results, always apply CHATTAHOOCHEE SEALER in two (2) thin coats to achieve net square foot coverage rate. Do not thin product. 

 

• For EXTERIOR application ONLY.
• Perform a test to ensure sealer compatibility.
• Brush may be used where roller won’t reach.
• Do not pour directly from container onto concrete.
• Use ¾” to 1 ¼” nap to evenly coat stones

 

Keep roller soaked and apply vertically, or horizontally, to entire area, maintaining a wet edge to avoid roller marks. Wait until the surface is tack-free (approx. 4 hours) before applying a second coat by cross-rolling perpendicular to the first coat ensuring complete coverage. Foot traffic should be avoided for 4-6 hours. Vehicle traffic should be avoided for 48 hours.

 

• Do not apply if rain is imminent.
• Cooler temperatures or increased humidity may slow the drying time.

 

 

NET COVERAGE RATE

Approximately 100 sq. ft. per gallon. Older or very porous surfaces may require several coats.

 

To calculate your total area square footage (length X width = total square feet) to determine the amount of product you’ll need to properly meet the suggested net coverage rate.

 

CLEANUP

Clean up tools with Xylene, Toluene or Lacquer Thinner.

Do not use Paint Thinner, Mineral Spirits or water.

 

MAINTENANCE

Clean sealed surface with water only. Reseal surface as needed, but not more than every two years to prevent buildup of sealer.

24 HOUR & EMERGENCY INFORMATION

INFOTRAC 1-800-535-5053

 

WARNING: Strong solvent smell.

 

COMBUSTIBLE

EYE, SKIN AND RESPIRATORY IRRITANT

Contains Aromatic Naphtha. Do not use near heat, sparks or open flames. Avoid contact with eyes and prolonged contact with skin. Use only with adequate ventilation. Do not inhale vapors. Do not ingest.

 

FIRST AID

• In case of eye contact, flush with water for 15 minutes.
• In case of skin contact, wash thoroughly with soap and water.
• If swallowed, do not induce vomiting.
• Immediately contact hospital ER or physician.
• If vapors are inhaled or breathing becomes difficult, move person to fresh air immediately.
• Seek medical attention if skin, eye or respiratory irritation persist.

 

See Safety Data Sheet for more information

 

 

TECHNICAL DATA

Color/Type:               Clear Liquid

Active Content:         75%

Total Solids:              25%

VOC:                         Standard <600 g/L

Flash Point:               105° F

Freeze Point:             N/A

Storage:                    Inside, well ventilated. Keep container in dry area.

Shelf Life:                  2 years in tightly sealed, unopened container

 

STORAGE AND HANDLING

DO NOT modify sealer mix with other chemicals. Store in a cool dry place away from potential ignition sources. Keep container tightly sealed when not in use. Published shelf-life based upon upright storage of manufacturer-sealed containers kept in a cool dry area. Store in temperatures from 45⁰F to 100⁰F. Always dispose of unused product and container in accordance with local, state and federal guidelines.

Sealer Type:

Acrylic

 

Net Weight (lbs.):

5 Gallon - 45

1 Gallon -   9

 

Substrate Surface Type:

Smooth Troweled - NO

Textured or Stamped - NO

Broom Swept - NO

Exposed Aggregate - NO

Pavers - NO

Color, Dye or Stained – NO

Epoxy-set Stone Surface - YES

 

Net Coverage Rate (2 coats):

Approx. 100 sq. ft. per gallon

 

Number of Coats:

2

 

Time Between Coats:

Approx. 4 hrs.

 

Application Method:

Rolled

 

Available Color(s):

Clear

 

Interior/Exterior:

Exterior

 

Sheen:

Hi-Gloss

 

Dry to Touch:

2 – 4 hrs.

 

Foot Traffic:

4 – 6 hrs.

 

Vehicle Traffic:

48 hrs.

 

Water/Solvent Base:

Solvent

 

Low VOC:

N/A

 

Odor Type:

Strong Solvent Odor

 

Warranty:

None

FREE SHIPPING is Standard UPS Ground shipping on parcel and residential delivery for all purchases over $50.00 made on eaglesealer.com, and does NOT include EXPRESS or EXPEDITED shipping. Some exclusions apply. Due to Federal DOT shipping regulations with paint related products, overnight, air deliveries or Solvent Based Low VOC sealers are NOT available for standardized shipping. Please contact our office for shipping options. EAGLE reserves the right to change or end this offer at any time.

 

EAGLE cannot ship to APO/FPO, P.O. Boxes, Alaska, Hawaii or U.S. Territories. For most shipments, please allow 1-2 business days for order processing and 3-5 business days for standard ground delivery in addition to order processing time. Holiday deliveries may be delayed so please take into consideration.

 

RETURN POLICY

If you would like to return any EAGLE product, we will issue a refund under the following conditions: (1) the product is returned to our facility within 30 days from the receipt of the product. (2) The product must be returned unopened and in its original condition. (3) Customer is responsible for return shipping charges, and a 20% restocking fee per order. NO EXCEPTIONS. (4) A refund will be issued within 7 days of returned product received by EAGLE I.F.P. Company, minus the 20% restocking fee AND minus return shipping charges incurred. Collect shipment will not be accepted. Refund will be issued to original payment method ONLY. Return intructions here.

Since Manufacturer has no control over handling, use or storage; no guarantee express or implied, is offered. The suitability of the product for use shall be solely up to the user. Manufacturer retains the right to venue.